Make a DIY Rustic Wooden American Flag

I made a Rustic Wooden American Flag to hang in my office.  This is a fun project that is easy to make using supplies from the home center.  Watch my video, then read further for a list of supplies, instructions, and photos.

Below is a list of supplies that I used on this project:

• One 15" length of a pine 1x12 board.
• Five 8-foot 1x2 pine boards.
• Wood Glue
• Picture hanging wire, 2 washers, 2 screws for the hanger.
• Minwax Tintable Water-Based Stain (Below are the Lowes formulas for custom tinting the stain Scarlet Red and True Blue, in case they remove them from their standard color list.)

Lowes Stain Formulas

Designing the Stars in the Inventables EASEL PRO Software

Here are the basic instructions for this project:

1. Cut six 37" stripes.
2. Cut seven 22" stripes.
3. Cut four 19" braces for the back.
4. Cut one 10.5"x15" panel.  (Note: The 1x2's from the home center can vary in width.  Measure the height of the seven short stripes and cut the panel to match.)
5. Round over the front edges with a 1/8" roundover bit in a router.
6. Use a blow torch to scorch the wood (if desired).
7. Stain three 37" stripes and four 22" stripes Scarlet Red.
8. Stain the panel True Blue.
9. Add the stars to the panel.  I used my Inventables X-Carve CNC Machine and the EASEL PRO software to engrave the stars with a 90 degree V-Bit.  Click here to open my Stars project.
10. Glue the flag together using minimal wood glue to avoid lots of squeeze out.
11. Clamp the flag to pull it all together.
12. Attach the four braces to the back with glue and nails.  Make sure one brace overlaps the joint between the union and the shorter stripes.  Space them evenly.
13. Spray with a clear coat finish.  I used Deft Clear Wood Finish Satin Lacquer.

Assembling the Flag

If you don't have a CNC machine, check out these other options for adding stars to the panel:

• Paint and Stencil - Use a stencil to paint the stars.  Click here to order one for a 19.5"x37" flag.
• Hand Carving - Print a paper template to use as a guide to carve the stars with a carving knife.
• Dremel Tool - Draw the stars onto the panel using a template, then engrave them with a Dremel tool.
• Laser Cut Stars - Glue on some laser cut stars.  Click here to order a pack of 1.25" stars for a 19.5"x37" flag.

Hang the Flag using Picture Wire, Washers and Screws

This was a fun project and it looks awesome!  You can get really creative with the blow torch effect.  These flags are very popular and sell well if you would like to try to make some money from your woodworking.  God bless the U.S.A!

DIY Rustic Wooden American Flag by The Carmichael Workshop

Clicking a referral/affiliate link in this article and making a purchase will help to support my channel via a small referral fee from the merchant.  Thank you for your support!

Making a Rubik's Cube Birdhouse

I built this birdhouse to look like a classic 1980's Rubik's Cube.  Watch my video of the process and read further for more information and pictures.

To make the birdhouse, I tilted my table saw blade to 45 degrees, then cut six 9" squares with bevels on all sides.  I drilled a 1.5" hole in the front and glued together the sides and top.

I glued a cross piece in the bottom opening so that I would have something to screw the bottom to.  I also drilled some ventilation/drainage holes inside the grooves on the yellow bottom piece.

Just for fun to finish it off, I printed the classic Rubik's Cube logo on a label and stuck it on.

I made a display stand for it.  It's just a square piece of plywood with three boards glued on in the shape of a triangle.  It will probably remain on display in my shop with all of my other crazy birdhouses.  Click here to check those out too!